Hallo Mein TQS ist endlich da.
Wer auch einen Warthog ablöst:
Zuerst den Warthog in der Device Config durch den TQS ersetzen (Die Komplette Zeile TQS welche am dende der Device Config stehen sollte an Die 2. Stelle Kopieren (Da soll immer der Throttle sein)
Danach in der Keyfile eure alten Warthog zuweisungen durch dies ersetzen:
Code
- #################################################################
- ###
- ### TM TQS DX button mapping for the THROTTLE only,
- ### this is the UNSHIFTED (without holding Pinky/S3) layer.
- ###
- ###
- ### Note:
- ###
- ### The TM TQS Throttle does not provide a descrete DX button
- ### for each switch state. Hence BMS offers a special syntax to
- ### circumvent these limitations.
- ###
- ### - Normal: ... -1 -2 0 0x0 ...
- ### - Press: ... -2 -2 0 0x0 ...
- ### - Release: ... -2 -2 0 0x42 ...
- ###
- #################################################################
- SimDoNothing -1 0 0XFFFFFFFF 0 0 0 -2 "======== THROTTLE UNSHIFTED ========"
- # Curser Press
- SimCursorEnable 43 -1 -2 0 0x0 -1
- # MSP (Mic Switch Press) (Win DX34 = BMS DX33)
- ToggleNVGMode 36 -1 -2 0 0x0 -1
- # UHF
- SimTransmitCom1 33 -1 -2 0 0x0 -1
- # IFF IN
- SimCommsSwitchRight 34 -1 -2 0 0x0 -1
- # VHF
- SimTransmitCom2 35 -1 -2 0 0x0 -1
- # IFFOut
- SimCommsSwitchLeft 32 -1 -2 0 0x0 -1
- # SPDF (SpeedBrk Fwd)
- AFBrakesIn 41 -1 -2 0 0x0 -1
- # SPDB (SpeedBrk Back)
- AFBrakesOut 40 -1 -2 0 0x0 -1
- # This one has its own syntax as it makes use of PRESS & RELEASE features.
- # Please refer to the key file manual for more information.
- # Dogfight switch
- # This is a PRESS comand:
- # -> DX button is moved from deactivated to activated state.
- SimSelectMRMOverride 38 -2 -2 0 0x0 -1
- # BSM (Boat Switch Ctr from Fwd) (Same DX #, but has instead of a "0" a "0x42".
- # This is a RELEASE comand:
- # -> DX button is moved from activated to deactivated state.
- SimDeselectOverride 38 -2 -2 0x42 0x0 -1
- # Note:
- # The following switches also follow the same rules.
- # BSB (Boat Switch Back) (Win DX42 = BMS DX41)
- SimSelectSRMOverride 39 -2 -2 0 0x0 -1
- # BSM (Boat Switch Ctr from Back)
- SimDeselectOverride 39 -2 -2 0x42 0x0 -1
- # Uncage
- SimToggleMissileCage 37 -1 -2 0 0x0 -1
- # IDLERON (Idle detent right - Back) (Win DX61 = BMS DX60)
- SimThrottleIdleDetentBack 49 -2 -2 0 0x0 314
- # IDLERON (Fwd from - Back)
- SimThrottleIdleDetentForward 49 -2 -2 0x42 0x0 314
- #Chaff Flare
- SimCMSUp 48 -1 -2 0 0x0 -1
- #Zoom Out
- FOVDecrease 44 -1 -2 0 0x0 -1 "VIEWGEN: Decrease FOV – Or Mousewheel"
- #Zoom in
- FOVIncrease 46 -1 -2 0 0x0 -1 "VIEWGEN: Increase FOV – Or Mousewheel"
- #Zoom Press
- OTWVRZoomToggle 45 -1 -2 0 0x0 -1 "VIEWGEN: VR Zoom - Toggle"
Danach ist euer Throttle belegt wie beschriftet.
Hinzugefügt habe ich:
Com Switch Press : NVG Toggle
Chaff und Flare Button Entspricht CMS UP ich wüsste nicht dass der Slap Switch Implementiert ist.
Mausrad rein Reinzoomen
Mausrad raus Rauszommen
Mausrad Drücken VR Zoom Toggle